Convertible hoods come with a recirculating kit or charcoal filters to convert the hood to ductless. A ducted hood, on the other hand, cannot be installed as ductless. While a ducted range hood is the first choice for most chefs and homeowners, both ducted and ductless hoods have their pros and cons.
For a more in-depth comparison of ducted vs ductless range hoods, check out this complete article. A ducted range hood pulls the smoke, grease, and unwanted contaminants through ductwork and outside your home, compared to a ductless hood which merely recirculates the air back into your kitchen.
With all the dirt and grime completely gone, your cabinets and the surrounding area will stay clean for much longer than they would with a ductless hood. Ducted hoods also remove strong odors from your kitchen, which is especially great if you cook Asian food or fried food.
Hoods that duct to the outside use stainless steel baffle filters or mesh filters which are dishwasher-safe. While cooking, the heat generated from the burners or grill can warm up the kitchen fast. But a ducted range hood can send this hot air outside your home in no time. With a ducted hood, you can cook comfortably and have an enjoyable experience in the kitchen. Inline blowers are no different than local blowers in terms of efficiency, but they are placed inside your ductwork —further away from your kitchen.
This drastically reduces the noise level or sones of your vent hood. You may not have the room for ductwork, which means you will either have to make room this can be expensive and time intensive or invest in a ductless hood. Since you need a professional to install ductwork, you will have to factor its installation into your budget. You have much more freedom in where you locate your ductless range hood. You are not bound by where ducting can go or already exists.
When remodeling, a ductless range hood can be reinstalled at another location. Although ductless hoods are not as powerful as ducted hoods, they are incredibly quiet. Believe it or not, the low CFM comes with an advantage — noise level — especially with an efficient blower or blowers. The number one disadvantage of a ductless range hood is that it is incapable of removing as many air contaminants as a range hood that vents outside. This means your kitchen may become quite humid while cooking — and smells may linger for a longer period of time.
Charcoal filters cannot filter out smoke and grease fully which could result in cooking odors and grease build up on kitchen surfaces. Charcoal filters need to be replaced every three to six months, or after about to hours of cooking. If you are contemplating installing a range hood that will vent outside, make sure you carefully consider the pros and cons.
Even though ducted range hoods are preferred, they might not always be the right option. Some homeowners may be fine with a ductless range hood if they live in an apartment, do not cook very often, enjoy low-intensity cooking, or prepare cuisine with fewer strong odors, such as vegetarian.
Rigid duct is without a doubt the best option for venting your range hood. Rigid duct is higher quality than flex duct and is made of much more durable materials.
For more information on choosing the right type of duct for your range hood, check out this article. No; range hoods without a duct, or ductless range hoods, can recirculate air back into your kitchen. However, to clean your kitchen air most efficiently, purchase a ducted range hood. Rather than relocate the cooking exhaust, it will evacuate it from your home entirely.
This drastically improves your indoor air quality and is beneficial for your health and safety in the long-term. The shorter the duct, the better. If your ductwork is too long, your kitchen air may not reach the outside. Backdrafting can also occur, where air stays inside your duct, flows back through your hood, and into your cooking space.
A range hood should stick out at a minimum half the length of your kitchen range and typically does not extend past its full length. Learn more in this complete article.
Line up the two holes on the blower to the two curved channels on the mounting bracket that are facing away from the wall. Orient the blower so that the longer tapered side is facing up and toward the direction that the air will be forced.
See Illustration for Step 2. Fasten the blower to the mounting bracket using the machine screws provided with the blower.
After installing the blower to the bracket, it is now time to install the previously installed ductwork to the blower. This may require transition pieces B if your inline blower A does not match the diameter size of ducting C you are using. See diagrams for Step 4.
If your duct work set up does not require transition pieces proceed to the next bullet point. Place the transition pieces B on both ends of the blower A. Using your drill, screw three self-tapping screws, spaced evenly around the circumference of the transitions, through the transitions into the blower. Generously wrap the seams of the connections with Aluminum HVAC tape to seal any airflow that may escape. Place the duct work C on both ends of the blower A , or pre-transitioned blower.
Using your drill, screw three self-tapping screws, spaced evenly around the circumference of the ducting, through the ducting and in to the blower or transition pieces. Generously wrap the seams of the connections with aluminum HVAC tape to seal any airflow that may escape. All Proline hoods come with either an aluminum mesh or stainless steel baffle filter. Both types of filters are dishwasher safe for easy cleaning.
For three years from the date of original purchase, we will replace any parts or components that failed due to manufacturing defects. Only the original purchaser for residential products purchased in the continental United States limited warranty in Canada, Hawaii, and Alaska.
Hawaii, Alaska, and Canada must pay regular shipping rates. You will be responsible for all return shipping costs. We can help arrange for a pickup if requested. NOTE: We will only allow one undamaged exchange per purchase. Your replacement hood must be of equal or lesser value. If the value of your replacement hood is higher, you will be responsible for paying the difference in price.
We hope this information helped you better understand how to install a vent hood. At Proline Range Hoods, we make our range hoods and vent hoods easy to install at any step of the process. We also have many videos on how to install range hoods on our website. Table of Contents. How to install range hood vent ductwork Marking the location as to where you want to install the vent. Depending on the size and design of the kitchen, mark it on the wall, where the vent will come out on the range hood.
Cut the hole in the wall for Rang Hood Vent. Before cutting a large hole in the wall, make sure there are no electrical or plumbing lines behind the wall. Make sure u cut a hole that is larger in size than the vent, it will enable you to run the electric cable from the range hood.
Cut the opening for the vent pipe. This step requires drilling from the inside and cutting the wall from the outside. Next, you need to attach the vent cap to the wall with screws, you can use caulk and screws for tight sealing. Cutting of duct damper comes next. You need to size the damper to the hole that has to be duct. Place a piece of duct in the hole to make sure you have enough space. Then with help of the interior damper, mark from outside where to tape the ductwork. Electrical line installation.
0コメント